XhorsevvdiShare

  Question: VVDI MB read an EIS of a Mercedes C270 W203 2002 via OBD, and it says "Can't start communication with EIS, check connection!". Try via IR, and it says "Current EIS don't support read password via IR!".   Here Xhorsevvdi gave the Solution: 1.Select IR mode if trying via IR 2.If the error remains, then remove EIS and read it using VVDI PROG 1)Read by soldering 2)Read by Xhorse EZS Adapter Hope this could help! http://blog.xhorsevvdi.com/vvdi-mb-read-w203-eis-via-obd-and-ir-fail-solution/

  Problem: Xhorse Dolphin II , set up same high like cutting part and two times when was reading key broke. The prompt shows "ERROR CODE 17 Not detected key" Here Xhorsevvdi gave the Reason: Dolphin XP005L decode (learn) keys via conductivity, so the probe will get broken if keys are 1)Aluminum or plastic 2)Dirty or oxidized   Solution: 1)Clean keys esp. bittings using a brush, a blade, cleaners etc. 2)Work with Xhorse Key Reader to avoid breaking probes (this device identifies keys not via conductivity, so don't need to worry if keys are plastic or clean)   How to Detect Non-conductive Parts? 1)Ensure key is metal not aluminum or plastic 2)Electrical Conductivity Measurement/ Sport detection on Xhorse app Path: Device Information>> Electrical Conductivity Measurement>>Probe and Clamp/ Spot detection 3)Multimeter   Hope this could help! http://blog.xhorsevvdi.com/dolphin-xp005l-error-code-17-not-detected-key-solution/

  This article is going to show you how to add a key for Jeep Wrangler 2020 when all key lost.   Tools: VVDI Key Tool Plus Autel KM100 12+8 Bypass Cable Autel Universal Key   Generate Autel universal key. On Key Tool Plus Pad , Select Immo Programming>>Jeep>>Select by area>>North America>>Wrangler>>2020-2021>>Smart key system Connect 12+8 bypass cable as prompt. Turn on emergency light and click "Read PIN code". This process requires network connection, and it is normal to see the prompt "Calculate failed". Wait for 8-10 minutes, then we have the password. Go to "Add smart key", and enter the password. Press start button using new key as guided. Complete.   https://www.xhorsevvdi.com/

  Here we are going to share with you the support list of VVDI BE Key Pro . Compatible VVDI BE Key (Non-smart): VVDI BE Key Pro Green (with 200 points for MB key pass calculation) VVDI BE Key Pro Yellow (without 100 points)   Support List: Brand Model Year Chassis MERCEDES BENZ CLA200 2013-2017 W117 MERCEDES BENZ GLK280 2008-2009   MERCEDES BENZ B200 2005-2017 W245 & W246 MERCEDES BENZ SLK280 2005-2009 W171 MERCEDES BENZ E420 1997-2009 W210 & W211 MERCEDES BENZ S430 1998-2006 W220 MERCEDES BENZ C30 2004-2007 W203 MERCEDES BENZ G63 2002-2018 W463 MERCEDES BENZ S65 2005-2013 W220 & W221 MERCEDES BENZ E230 1998-2009 W210 & W211 MERCEDES BENZ S250 2009-2013 W221 MERCEDES BENZ C36 1997-2000 W202 MERCEDES BENZ GL63 2013-2016 W166 MERCEDES BENZ SL55 2003-2006 W230 MERCEDES BENZ CLS250 2014-2017 W218 MERCEDES BENZ ML350 2012-2015 W166 MERCEDES BENZ A170 2011-2012 W169 MERCEDES BENZ VITO 2004-2017 W639 & W447 MERCEDES BENZ E550 2003-2016 W211 & W212 MERCEDES BENZ S55 2

  Question: Xhorse VVDI PROG read MC68HC908JK1, then program says "Try Frequency failed Chip unconnected(00)". Here Xhorsevvdi shows the possible Solution: 1.Check connection by the diagram 2.Heat chip 3.Adjust VCC to 4.5-5.0v and read again 4.If the error remains, it means that the chip is encrypted and VVDI PROG don't support it.   http://blog.xhorsevvdi.com/vvdi-prog-read-mc68hc908jk1-chip-unconnected-solution/

  Here is a review of Xhorse VVDI2 Key Programmer : Audi R8 2012 Spare Key Programming Success.   1.Add Key Connect VVDI2 to vehicle via OBD port. Try auto detect. Instrument type is "A3/ TT/ R8 (CDC32XX)". Read EEPROM. Read IMMO data. New key into VVDI2's programming coil. Then select Make Dealer Key>>Audi>>Prepare normal dealer key Add Key. Read Immo data to verify the key is learned.   2.Remote Adaptation Go to Key Learn>>Remote Key Adaptation>>BCM Remote Key Adaptation>>Learn remote control Take off key, press UNLOCK button in 15 seconds. Remote programming done. Done, and this keydiy control works. http://blog.xhorsevvdi.com/audi-r8-2012-spare-key-programming-using-vvdi2-with-keydiy/

  Xhorse Dolphin XP-005 is designed for cutting sided/ track/ tibbe keys. Here we will share with you the support list. Dolphin XP-005 Support List (2020-01-21): BRAND CARS Key Profile Code Key Code Series Xhorse ID Cuts MARUTI Maruti Swift, Dzire etc. HU133R/HU87R IP5001-IP6308 1098 10 MARUTI Swift, Dzire, New Wagonr Swift-New only duplication 16360 10 MARUTI Suzuki Alto/WagonR/Eeco Swift-New 71001-72500 1270 8 MARUTI Suzuki Omni SZ13RP 6501-7704 30 7 HYUNDAI Hyundai Santro HYN10 R1-1000 8 8 HYUNDAI Hyundai Verna (old model) HYN11/HYN15 V1-V2500 1753 8 HYUNDAI Hyundai Accent /Elantra HYN11/HYN15 T1-1000 8 8 HYUNDAI Hyundai New i20/Xcent HYN14 M1-2500 1507 8 HYUNDAI Hyundai i20 Elite HYN14 P1-2500 1507 8 HYUNDAI Hyundai i20 (old) HY22 P1-2501 1360 6*6 HYUNDAI Hyundai i10/Eon HYN14 P1-2502 1507 8 HYUNDAI Hyundai Verna Fluidic (2010-2017) VERNA 85001-87079 16005 8 HONDA Honda City, Civic, Accord, Jazz HON66 K001-N718 2086 6*6 HONDA Honda Amaze/Brio BRIO 25001-28081 16111 6*6 TOYOTA Toy

  Whole process you need: VVDI Key Tool Plus Dolphin XP-005 Key Cutting Machine VVDI Smart Key Key blade for Cadillac ATS This blog is about Xhorse VVDI Key tool Plus Program Cadillac ATS key 2014 year, and key tool max + dolphin xp005 cut Cadillac key OK, you can also use key tool plus+XP005 Key cutting , use key tool plus as screen.   1.       Generate remote Choose Cadillac ATS in the vehicle list. Put the vvdi mart key into coil, then press generate.   2.       Use key tool plus program Cadillac ATS 2014 year key Choose "immo programming" in key tool plus main menu. Then choose Cadillac>>read pin code Start programming After read pin code OK, then back the Cadillac menu, choose ATS type.   -2016 Smart key programming Start programming Smart keys adding Click Yes to continue   3.       Key tool max + dolphin xp-005 cut Cadillac key Put original key blade on the clamp, do the decode After decode OK, put new key blade to do the cutting process Key blade cut OK.   4.